PRODUCT DATA SHEET
LIQUID RUBBER ZAVLAR™
Liquid Rubber Zavlar ™ is a modified elastomeric asphalt emulsion specifically
formulated to be applied by brush, squeegee or specially designed spray equipment.
Liquid Rubber Zavlar ™ is a cold applied single component product designed
for a wide range of protective coating applications. The product technology
employed in Liquid Rubber Zavlar ™ provides a solvent-free, quick setting
coating that yields a membrane with excellent strength, elasticity and adhesion.
Liquid Rubber Zavlar ™ is an environmentally friendly waterproofing
product which can be applied indoors and outdoors with no special protective
equipment.
* Free of flammable solvents * Non-toxic * Odourless and Water based
PHYSICAL PROPERTIES
| Property | Typical results |
| Specific gravity (liquid) g/cm3 | Approx. 1.0 |
| Odour | None |
| VOC | Contains no solvents |
| Colour | Brown to black |
| % solids (wt) | 53-58 |
| Viscosity, Brookfield, sp.#5, 20 rpm | 8000-9000 |
| pH | 10-12 |
PERFORMANCE (cured membrane)
| Property | Typical results |
| Colour | Black |
| Specific gravity, g/cm3 | Approximately 1.0 |
| Chemical resistance | Resistant to most inorganic solutions. Not recommended for gasoline or other petroleum products. Consult Chemical Resistance chart for further information. |
| Biological resistance ASTM E 154, ASTM D412 | Passed (> 90% original value) |
| Impact resistance CSB 37-GP-56 @ 23oC, in-lbs Water tightness after impact |
Passed (168) Passed (no leakage) |
| Tensile strength ASTM D412, psi | 90 |
| Elongation, % | 850 |
| Accelerated weathering, ASTM G 155, D 412 Tensile strength |
Passed (No deterioration of film) Passed (> 90% original value) |
| Hardness, Durometer Type 00 | 85-87 |
USES
Liquid Rubber Zavlar ™ is used as a protective coating to prevent water
and corrosion damage. Liquid Rubber Zavlar ™ can be used for rust protection
of ferrous materials and is also of value for noise and vibration dampening.
It may also be applied to concrete structures, slabs and parking decks. The
high viscosity of Liquid Rubber Zavlar ™ allows it to be used to cover
small cracks, or to coat vertical surfaces.
APPLICATION
Liquid Rubber Zavlar ™ is water based environmentally safe alternative
to conventional hot-applied or solvent based waterproofing systems. When cured
it will form a seamless flexible membrane.
Liquid Rubber Zavlar ™ is a single component product that may be applied
using a brush, roller or squeegee. It may also be spray applied using a specially
designed spray system. Since Liquid Rubber Zavlar ™ cures by evaporation,
an application temperature of 15-20°C is recommended. Apply in thin coats.
The product fully cures within 24 hours at 20oC (70oF) and 50% relative humidity,
when applied at a thickness of 40 mils (1 mm).
Liquid Rubber Zavlar ™ should be applied to a dry surface which is free
of dirt, debris, oil or grease. Application is not recommended if heavy rains
are imminent, or in high humidity environments. For best results apply in
thin coats. With joints or cracks in the surface a fabric reinforcing layer
may be recommended. See application manual or consult with your Liquid Rubber
Engineered Coatings representative for further details.
Liquid Rubber Zavlar ™ is applied between 0.3-0.7 m2/litre (15-30 ft2/gal)
to produce a 40-120 mil (1-3 mm) protective membrane. Typically Liquid Rubber
Zavlar ™ dries to the touch in one minute @20°C and is completely
cured in 48 hrs. This curing time may vary depending on temperature and relative
humidity.
LIMITATIONS
Liquid Rubber Zavlar ™ is mildly alkaline. When applying this product
observe appropriate safety precautions, wear gloves, eye protection and other
suitable protective equipment.
For further information please consult the product MSDS.
Liquid Rubber Zavlar ™ should not be applied when the ambient temperature
is below 15°C. The uncured membrane may be damaged if frozen. Do not apply
to wet surfaces or directly before a rain. Some surface base coat materials
such as coal tar are unsuitable for use with Liquid Rubber Zavlar ™.
CAUTION
For industrial use only. Keep out of the reach of children. Avoid storage
below 5°C.
Please consult the Material Safety Data Sheet before using Liquid Rubber Zavlar
™.
TECHNICAL SERVICE
Telephone (07) 55 765 322
THIS PRODUCT IS NOT SUBJECT TO THE CONTROLLED PRODUCTS REGULATIONS.
Liquid Rubber Zavlar™ is manufactured exclusively by Liquid Rubber Engineered
Coatings, A division of Liquid Rubber Industries Inc., 89 Scollard St., Toronto,
ON, M5R 1G4 Canada.
Australian division, Liquid Rubber Australia Pty Ltd, 2 / 57 Township Drv
West Burleigh, QLD 4220.
Effective: 06-Jan-06
Replaces: 21-Nov-04
The information contained herein is based on available data and is provided
for information only. Liquid Rubber Industries Inc. and respective subsidiaries,
makes no warranties, guarantees or conditions, expressed or implied, regarding
the accuracy of the data or its use therein. Liquid Rubber Industries Inc.
including its subsidiaries, Liquid Rubber Australia Pty Ltd, will not be liable
for any damages arising from the use of the information product described
on this data sheet. Product data is subject to change without notice. Unless
otherwise stated, Liquid Rubber Industries Inc. and respective subsidiaries,
sole warrantee shall be the replacement or refund of purchase price for any
product found not to meet the above specifications.